Bondtech LGX® Lite Extruder

769 kr

Tilgjengelighet 1 på lager

Kategori:

Bondtech LGX® Lite Extruder (uten motor)

Bondtech LGX-Lite Extruder

Bondtech LGX Lite er en filamentextruder basert på LGX “Large Gears eXtruder”, og bruker Bondtech sin nye Dual Drive teknologi basert på store drivgir

  • Større drivhjul for forbedret filamentgrep
  • Presatt filament tensionhendel, for repeterbare resultat
  • Vindu til drivhjulene gir enkelt vedlikehold
  • Kompakt, lett i vekt og symmetrisk design. Sentrert filamenthull for forbedret prestanda og kompabilitet.
  • Flere monteringshull gir enkel montering og fleksibelt oppsett
  • Produsert på SLSprinter med PA12Nylon for maksimal styrke og høyere temperaturresistanse
bondtech lgx,large gear extruder,bondtech large gear extruder,bondtech extruder,lgx,lgx lite,lgx lite extruder,lgx-lite

Viktig informasjon:

Esteps verdi:
400 ved bruk av 16 microsteps
800 ved bruk av 32 microsteps
Anbefalt strømmengde mellom 0.45 – 0.65A

Bondtech LGX-Lite er en ny kompakt og simplere versjon av LGX, parret med en LDO Nema14 rund 20mm Stepper Motor.
(Extruderen kan kjøpes både med og uten motor)

LGX-Lite har veldig liten formfaktor og lav vekt, og er laget som et Bondtech alternativ til andre interessante og kompakte extrudere som feks Orbiter, HextrudORT og Sherpa Mini.

 

Viktig informasjon

Bruk LGX Lite kun med en 36mm rund steppermotor som har 10tannet drivhjul slik som dette:
Hvis ikke kan extruderen bli skadet og dette dekkes ikke av garanti

bondtech lgx,large gear extruder,bondtech large gear extruder,bondtech extruder,lgx,lgx lite,lgx lite extruder,lgx-lite

LGX Lite med stepper motor er inkludert:

1x LGX Lite Extruder
1x LDO Nema 14 20mm Rund pancake steppermotor m/ 1m lang kabel og JST-XH4 pin
1x 2mm Hex nøkkel
1x “Powered by Bondtech” klistremerk
1x Push Fit Collar
1x 30mm PTFE Tube
8x M3 muttre for montering

 

LGX Lite uten stepper motor er inkludert:

1x LGX Lite Extruder
1x 2mm Hex nøkkel
1x “Powered by Bondtech” klistremerk
1x Push Fit Collar
1x 30mm PTFE Tube
8x M3 muttre for montering

LGX Lite Drawings, Geometries and more

Mounting Hole Patterns

There are 3 different mount hole patterns available:

  • One at the bottom with 4 holes.
  • Another on the flat left-hand side with 2 holes.
  • A third on the top with a single hole that may be used in tandem with the filament entry hole.

All holes must be reinforced with the M3 square nuts supplied, and are 5mm deep. To save weight, use only the necessary square nuts.

Find some drawings below. Units in mm.

bondtech lgx,large gear extruder,bondtech large gear extruder,bondtech extruder,lgx,lgx lite,lgx lite extruder,lgx-lite

Mounting With A Plate In Between
Extruder And Stepper Motor

An additional mounting hole pattern may be used. It is possible to separate the stepper motor from the extruder and mount them with a plate in between.

The plate must be from 2 up to 3mm thick. 2.5mm is recommended. To use this mounting solution, the extruder’s rear plate must be removed.

The plate should feature the 36mm round stepper motor mounting pattern with 2 M3 holes on the flanges and a Ø16mm central opening.

bondtech lgx,large gear extruder,bondtech large gear extruder,bondtech extruder,lgx,lgx lite,lgx lite extruder,lgx-lite

Here you may find the LGX® Lite simplified geometry to allow you preparing a mount setup.

The STEP file includes 3 bodies:

  • Extruder body;
  • Extruder rear mount plate;
  • 36STH20 Stepper motor.

It is possible to install the LGX® Lite with a plate in between the stepper motor and the extruder. In this case that plate replaces the extruder’s rear mount plate.

Max thickness of such plate is 3mm. Recommended thickness is 2.5mm.

bondtech lgx,large gear extruder,bondtech large gear extruder,bondtech extruder,lgx,lgx lite,lgx lite extruder,lgx-lite

To use a mounting plate thicker than 2.5mm, it is recommended to use longer screws than supplied.

Skroll til toppen