Panucatt Devices Azteeg X5 mini WIFI 32BIT All-in-one Controller

1,698 kr

Tilgjengelighet 1 på lager


Azteeg X5 mini WIFI 32BIT All-in-one Controller
The X5 mini WIFI is a 32 bit ARM based Motion controller for 3D printers, CNC Machines and Laser cutters. The X5 mini runs on Smoothieware firmware and is based on Smoothieboard by the awesome Arthur Wolf. The X5 mini WIFI uses the powerful 32bit, 120Mhz NXP LPC1769 ARM chip capable of faster calculations for faster and smoother movements without breaking a sweat.
Configuration is easier using a text based config file loaded on the SD card, no need to upload firmware every time you make a change. Just edit the config file from your PC then reboot the board with the new config and you’re done.
Wifi Module has its own separate web control page to control and operate the printer remotely. You can transfer files directly to the main SD card and edit the config file on any PC, Phone or Tablet using Wifi. Web Control can also display video when using an IP camera. Wifi Module firmware custom made by Luc Lebosse.
Compact and powerful all in one solution. WIFI, V2 & V3 Board size: 3.9″(100mm) X 2.2″(56mm) – ( V1 and V1.1 board size 3.4″(94mm) X 2″(50mm))
Changes from V3 to Wifi
– Wifi module replaces Ethernet
– Added analog input protection
– Added endstop input protection Changes from V2 to V3
– Ethernet onboard – RJ45
– V3 now uses modular drivers
– Compatible with pololu style drivers
– Digipot current adjustment using Panucatt Drivers
Changes from v1.1 to V2
– V2 uses THB6128 drivers with up to 1/128 micro-stepping @ 2 Amps max
– Larger single heatsink pre installed
– Added/changed expansion pins
– Added one more fan/switch mosfet
– Breakout pins for LAN function
– Solder Jumpers to slave drivers
– Direct plug-in expansion for mini Viki and Viki 2.0 Graphic LCDs.
– Slightly bigger board sizeRecommended Stepper Drivers for V3 and WiFi versions (with digipot current control)

  • SD2224 (NEW) – Based on Trinamic’s TMC2224 chip with Super Quiet Stealthchop2 mode, single wire UART programmable. Up to 1/32 microsteps (1/256 using UART programming).
  • SD5984 – Based on allegro’s new A5984 chips. Quieter and smoother than most drivers, 1/32 microstepping, 2 Amps 40V max. With Adaptive Percent Fast Decay feature.
  • SD6128 – Based on Sanyo’s THB6128 chips. Quiet and smooth like the SD5984, 1/128 microstepping, 2A 35V max.
  • SD8825 – Based on Ti DRV8825. Robust and runs cool. 1/32 microstepping, 2.5A 40V max. Good choice for heftier motors

Most 3rd party drivers will work with the X5 mini V3 but current limit adjustment for the driver needs to be done manually using the trimpot. Panucatt stepper drivers has extra pins to make use of the digipot feature.

  • 32BIT NPC LPC1769 120MHZ ARM processor.
  • Compatible with Smoothieware firmeware by Arthur Wolf
  • Wifi Module on-board with stand alone web Control (Ethernet built in – RJ45 for V3)
  • Digital pot stepper driver current control (Panucatt drivers only)
  • 1 High Current Mosfet for Heat bed control
  • 1 Mosfet for Hotend control
  • 2 FAN Mosfet ( 1 mosfet on V1 and V1.1)
  • 4 end stops and 2 thermistor inputs ( ESD/Over voltage protected inputs)
  • Wide input high efficiency switching Power supply (5v @ 1A max)
  • Micro SD card slot built in
  • High current Terminal blocks can Handle up to 20 Amps per pin
  • 4 Layer, 2oz per layer PCB
  • Over voltage protected analog inputs
  • ESD/Surge protected endstop inputs
  • Azteeg X5 mini WiFi controller board with Bootloader
  • Drivers if selected
  • Shunt jumpers
  • Micro SD card if selected
  • Driver w/ Heatsink If selected


Skroll til toppen